The Pillow Glass Mosaic Collection is designed for almost any commercial and residential interior and exterior application including floor accents, walls, ceilings, water features, countertops, backsplashes and more. It is not recommended for areas that may be subject to heavy impact, heavy abrasion, and areas where temperatures can exceed 130 degrees Fahrenheit.
There will be some variation in size and surface shape between each pillowed square, this variation is considered to be a desired feature in the Pillow Glass.
SOLI Pillow Glass Mosaic tiles can be installed around gently curved surfaces. Some manipulation of the tiles may be required in order to create uniformity between each sheet. The glass comes with a plastic front or mesh back, which can easily be cut with a utility knife.
All substrates should be firmly fixed, flat, clean, dry and free of contaminants such as dust, oil, paint, sealers etc. to ensure proper adhesion. Painted surfaces must be scuffed or sanded for the product and adhesive to bond correctly. Wet areas need special attention and require appropriate substrates, e.g. concrete, cement boards (compressed sheet), and/or treated plywood. The use of reinforced waterproof membranes is suggested, and in the case of installation where drainage is required (i.e., shower floor pans or spas), there should be a slope-to-drain ratio of at least 1/2 inch per foot.
Waterproof membranes prevent leakage of water through to the sub-floor framing and/or habitable spaces below. Particular attention must be paid to: carrying the membrane up the wall, outside shower boxes, installation of bond breakers, and sealing around penetrations. It is strongly recommended that membrane systems be used in all wet areas. Some systems may involve the use of a primer.
The glass can easily be cut with a curved splitting clamp or a glass cutter. The mesh back or plastic front can easily be cut with a utility knife. To create a more seamless look the glass pebbles can be removed from the mesh by hand and readjusted if necessary.
Follow the adhesive manufacturer’s instructions carefully. We do not recommend one brand of adhesive over another. Please check with your local tile supply store for alternative and comparable products.
The manufacturer's literature will explain if the adhesive product is suitable for interiors and/or exteriors, as well as walls and floors. Most thinset mortars with a latex additive (multipurpose and polymer modified thinsets) are adequate for installing glass. A cement-based adhesive is generally suitable on masonry substrates where no movement is anticipated. Where slight movement could occur through thermal or pedestrian loads, a modified cement adhesive should be used as a minimum.
||A 1/4" – 1/8" notch trowel is recommended for most applications. Set the tile in place, gently tapping it in with a grout float to ensure 100% adhesive coverage.
We recommend using a white adhesive to show the true color of the glass, if a gray adhesive is used the color of the adhesive will show through the tile. Suggested adhesives include but are not limited to:
Mapei: Adesilex P10 (bright white) non-sag mortar for glass tile. Mix with water or Keraply.
Mapei: Kerabond Premium Dry-Set Mortar (Ker 102) mixed with Keralistic Mortar Admix (Ker 310).
Custom Building Products: Premium Plus Thin-Set Mortar (white) mixed with Custom Flex Ultra-Strength Thin-Set Additive.
Custom Building Products: MegaFlex Ultimate Thin-Set Mortar (white). No admixture is necessary.
Hydroment: ReFlex Ultra-Premium Latex-Modified Thin-Set Mortar. No admixture is necessary.
Laticrete: 254 Platinum Multipurpose Thin-Set Mortar. No admixture
TEC (H.B. Fuller): Super Flex Premium Performance Universal Latex-Modified Thin-Set Mortar. No admixture is necessary.
Grout should be suitable for joints up to 3/4" in width and designed for external or internal conditions whichever may be the case. Sanded grout is generally recommended for any grout joint larger than 1/8". Grouts are ordinarily a water mix but where some flexibility may be needed, a latex additive or similar product should be used. It is important to wait the interval recommended by the adhesive manufacturer before grouting to minimize dirt ingress between the squares and avoid the opportunity for dislodging.
In the event that one desires to better expose the glass pillows, it is suggested that during the grouting process, the installer repeatedly removes the excess grout from the joints by the use of a medium bristle brush and sponge. A non-sanded grout can also be used if the desired look is to expose the pillow effect.
The glass tiles do not have to be sealed but we strongly recommend sealing the grout after installation to help prevent it from absorbing stains.
Care & Cleaning
SOLI Pillow Glass Mosaic tiles must be regularly cleaned and maintained to extend the life and beauty of the tile. The glass can be cleaned with a neutral mild detergent, or glass cleaner. Any spills should be cleaned quickly to lessen the degree of the stain to the grout. Do not use abrasive cleaners, powders, scouring pads, steel wool or sandpaper. Do not let soap, bleach or other cleaning solutions set on the surface.